Crosman ACG357 Bedienungsanleitung PDF herunterladen

EVEN THOUGH YOU GO THROUGH THE UNLOADING PROCEDURE, CONTINUE TO TREAT THE AIRSOFT GUN AS THOUGH IT WERE

LOADED. DO NOT POINT AT ANYTHING YOU DO NOT INTEND TO SHOOT.

1. Make sure the AIRSOFT GUN is “ON SAFE” (Section 3A) and pointed in a SAFE DIRECTION.

2. Locate the cylinder (E).

3. With the gun pointed in a safe direction, push the (I) safety (cylinder release) (Fig. 2) button forward and hold.

4. While still holding the safety (cylinder release) (I) button forward, gently push the cylinder (E) from the right side of the gun to the left side.

5. Locate the ejector rod (J)

6. Press the ejector rod removing the clip (L).

7. With the gun pointed in a safe direction, look through the barrel and the cylinder to make sure the gun is completely unloaded.

8. If there is a BB in the barrel or cylinder or clip, use a cleaning rod (not included) to remove the BBs

a. If the BB is in the cylinder or clip, push the cleaning rod through to remove the BB.

b. If the BB is in the barrel, see section 8 on removing a jammed BB.

IMPORTANT: Never use sharp metal tools to remove BBs from the gun.

NOTICE: The AIRSOFT GUN must be charged with CO

when following these steps but remember, do not store your gun with a CO

cartridge in it.

6. Aim and Fire Safely

You and others with you should ALWAYS wear eye protection designed for airsoft to protect your eyes.

2. Always aim your AIRSOFT GUN in a SAFE DIRECTION.

3. Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce o or ricochet and hit someone or

something you had not intended to hit.

4. DO NOT re-use plastic BBs because they could possibly cause damage to your AIRSOFT GUN.

5. Your AIRSOFT GUN is designed for target shooting and is suited for both indoor and outdoor use. Always remember to place

your target carefully.

6. THINK about what you will hit if you miss the target.

7. Your AIRSOFT GUN is correctly aimed when the front sight blade is position exactly in the notch of the rear sight.

8. The top of the front sight blade should be even with the top of the notch in the rear sight. The bulls-eye should appear to rest

on the top of the front sight (Fig. 5).

9. When you are sure of your target and backstop, and the area around the target is clear:

a. Take the AIRSOFT GUN “OFF SAFE” (section 3B)

b. Aim

c. Pull the trigger to re

7. Maintain Your Airsoft gun

Put one (1) drop of Crosman 0241 Pellgunoil

on the tip of every CO

cylinder in order to properly maintain your AIRSOFT GUN.

2. DO NOT use petroleum distillate based oil or solvent and DO NOT over-oil as this can cause damage to your AIRSOFT GUN.

3. DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the AIRSOFT GUN in any way inconsistent with this manual may make your AIRSOFT GUN unsafe to

use, cause serious injury, especially to the eye, and will void the warranty.

4. If you drop your AIRSOFT GUN, visually check to see that it works properly before you use it again.

5. If anything seems changed, like a shorter or weaker trigger pull, this may mean worn out or broken parts. Call Crosman customer service for assistance before using

your AIRSOFT GUN again.

6. To clean the AIRSOFT GUN barrel

a. Spray a cleaning patch with Crosman Nitro Lubricant oil

b. With the cleaning patch on the rod, insert it into the barrel to clean

c. Swab the barrel 3-4 times

d. Repeat the swabbing procedure with a dry patch

e. The barrel is clean when the patches come out clean after dry swabbing

8. Clearing a Jam

NEVER look down the end of barrel to see if a jam has been cleared.

2. Make sure the AIRSOFT GUN is “ON SAFE” and pointed in a SAFE DIRECTION

3. Locate the cylinder (E).

4. With the gun pointed in a safe direction, push the (I) safety (cylinder release) (Fig. 2) button forward and hold.

5. While still holding the safety (cylinder release) (I) button forward, gently push the cylinder (E) from the right side of the gun to the left side.

6. Locate the ejector rod (J)

7. Press the ejector rod removing the clip (L).

8. With the gun pointed in a safe direction, look through the barrel and the cylinder to make sure the gun is completely unloaded.

9. If there is a BB in the barrel or cylinder, use a cleaning rod (not included) to remove the BB

a. If the BB is in the cylinder, push the cleaning rod through to remove the BB.

b. If the BB is in the barrel, insert the tapered end of the cleaning rod into the muzzle and CAREFULLY and slowly

apply pressure until the BB exits the barrel

IMPORTANT: Never use sharp metal tools to remove BBs from the gun.

9. Sight Adjustment

A. The rear sight may be adjusted to shoot higher or lower (elevation)

Turn the screw on the top of the rear sight (Fig. 6) clockwise to move the point of impact up

2. Turn the screw on the top of the rear sight (Fig. 6) counter clockwise to move the point of impact down

B. The rear sight may also be adjusted to shoot right or left (windage)

Turn the screw on the side of the rear sight (Fig. 6) clockwise to move the point of impact to the right

2. Turn the screw on the side of the rear sight (Fig. 6) counterclockwise to move the point of impact to the left

SPECIFICATIONS

Mechanism BB Revolver Power Source 12 gram CO

cartridge

Sights Front Fixed Blade Velocity Up to 425 fps (.20g BBs)

Sights Rear Fixed Notch Length 9.5 inches

Caliber/Ammunition 6 mm Plastic BB Safety Slide

Capacity Up to 8 BBs Weight 2 lbs.

PERFORMANCE

Your AIRSOFT GUN was designed to function best with Crosman

branded ammunition. Using other than Crosman branded ammunition may cause your product to malfunction and may

void your warranty. For optimum performance use Crosman ammunition only.

STOP DO NOT RETURN THIS PRODUCT TO THE STORE.

Save on gas and avoid the trip back to the store. Our customer service representatives are here to help. Contact us directly at 1-800-7AIRGUN (1-800-724-7486). You can also get

answers to frequently asked questions at www.crosman.com.

CUSTOMER SERVICE

If your AIRSOFT GUN is not functioning, we recommend that you call Crosman Corporation Customer Service at 1-800- 724-7486 or 585-657-6161. (International customers should

contact their distributor.) DO NOT ATTEMPT TO DISASSEMBLE IT! Crosman assumes no warranty responsibility if the gun has been disassembled.

LIMITED 90 DAY WARRANTY

This product is warranted to the retail consumer for 90 days from date of retail purchase against defects in material and workmanship and is transferable.

WHAT IS COVERED

Replacement parts and labor. Transportation charges to consumer for repaired product.

WHAT IS NOT COVERED

Transportation charges to Crosman for product. Damages caused by abuse, modication or failure to perform normal maintenance. Any other expense. CONSEQUENTIAL DAMAGES,

INCIDENTAL DAMAGES, OR INCIDENTAL EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

HOW TO OBTAIN WARRANTY PERFORMANCE

WARRANTY CLAIMS

USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to product. Package and return to Crosman Corporation, Routes 5 & 20,

Bloomeld, NY 14469.

International Customers: Please return product to your nearest distributor. If you do not know your distributor, please call 585-657-6161 and ask for our International Department

for assistance.

IMPLIED WARRANTIES

ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF

RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be preempted, it shall not be applicable. This warranty gives you specic legal

rights, and you may also have other rights which vary from state to state.

CROSMAN is a registered trademark of Crosman Corporation in the United States.

Fig. 5

Fig. 6

GF600

6mm BB CO

Powered

8 Shot Airsoft Revolver

(Single and Double Action)

OWNER’S MANUAL

Crosman Corporation

7629 Routes 5 & 20

Bloomeld, NY 14469

www.crosman.com

1-800-724-7486 ACG357-515

If you have any questions regarding your airsoft gun, please contact Crosman at 1-800-724-7486, 585-657-6161 or www.crosman.com.

READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE USING THIS AIRSOFT GUN. AND REMEMBER, THIS AIRSOFT GUN IS NOT A TOY. TREAT IT WITH THE SAME RESPECT

YOU WOULD A FIREARM.

THIS IS NOT A TOY. ADULT SUPERVISION REQUIRED. MISUSE OR CARELESS USE MAY CAUSE SERIOUS INJURY, ESPECIALLY TO

THE EYE. EYE PROTECTION MUST BE USED BY THE USER AND ANY PERSON WITHIN RANGE. MAY BE DANGEROUS UP TO 100 YARDS 91.44 METERS. READ

OWNER’S MANUAL BEFORE USING.

YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR SHOOTING GLASSES TO PROTECT YOUR EYES.

READ ALL INSTRUCTIONS BEFORE USING.

BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND OWNERSHIP OF THIS AIRSOFT GUN.

DO NOT BRANDISH OR DISPLAY THIS AIRSOFT GUN IN PUBLIC  IT MAY CONFUSE PEOPLE AND MAY BE A CRIME. POLICE AND

OTHERS MAY THINK IT IS A FIREARM. DO NOT CHANGE THE COLORATION AND MARKINGS TO MAKE IT LOOK MORE LIKE A FIREARM. THAT IS DANGEROUS

AND MAY BE A CRIME.

THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH

DEFECTS OR OTHER REPRODUCTIVE HARM.

1. Safety First

• ALWAYS treat the AIRSOFT GUN as though it is loaded and ready to re.

• ALWAYS treat AIRSOFT GUNs with the same respect you would a rearm.

• ALWAYS store the AIRSOFT GUN unloaded.

• ALWAYS store the AIRSOFT GUN away from children.

• ALWAYS aim in a SAFE DIRECTION.

• ALWAYS keep the muzzle of the AIRSOFT GUN pointed in a SAFE DIRECTION.

• ALWAYS keep your nger o the trigger and out of the trigger guard until ready to shoot.

• ALWAYS keep the AIRSOFT GUN “ON SAFE” until you are ready to shoot (see section 3A).

• ALWAYS check to see if the AIRSOFT GUN is “ON SAFE” (see section 3A) and unloaded when receiving it from another person.

• ALWAYS have you and others wear shooting glasses to protect your eyes.

• ALWAYS wear shooting glasses over eye glasses if your prescription or reading glasses are not safety glasses.

• ALWAYS place the backstop in a location that will be safe should the backstop fail.

• ALWAYS check your backstop for wear before and after each use. All backstops are subject to wear and will eventually fail. Replace your backstop if

the surface is worn or damaged, or if a ricochet occurs.

• ALWAYS use the proper size BB in your AIRSOFT GUN. Check the markings on your AIRSOFT GUN to verify the BB size is 6mm.

• NEVER reuse ammunition.

• NEVER shoot at hard surfaces or at the surface of water. The BB may bounce o or ricochet and hit someone or something you had not intended

to hit.

• NEVER attempt to disassemble or tamper with your AIRSOFT GUN. Modifying the function of your AIRSOFT GUN in any way, may be unsafe and will

void your warranty.

• NEVER point the AIRSOFT GUN at any person or at anything you do not intend to shoot.

2. Learning the parts of your new airsoft gun

Learning the names of the parts of your AIRSOFT GUN will help you understand your owner’s manual.

Fig. 1

A. Rear Sight

B. Barrel

C. Front Sight

D. Muzzle

E. Cylinder

F. Trigger

G. Trigger Guard

H. Grip

I. Safety (Cylinder Release) (Fig. 2)

J. Ejector Rod

K. Hammer

L. Clip

M. Piercing Wing

3. Operate the Safety

IMPORTANT:

The AIRSOFT GUN can only be put “ON SAFE” when the hammer (K) is NOT

cocked. Like all mechanical devices, an AIRSOFT GUN safety can fail. Even when the safety is

“ON SAFE”, you should continue to handle the AIRSOFT GUN as if it is “o safe.”

NEVER point the AIRSOFT GUN at anything you do not intend to shoot.

A. Put the Airsoft Gun “ON SAFE”

Ensure the AIRSOFT GUN is pointing in a SAFE DIRECTION and the hammer

(K) is not cocked.

2. Locate the safety (I) on the left side of the AIRSOFT GUN.

3. Slide the safety toward the “S” or rear of the gun (Fig. 2).

4. The safety is NOT “ON SAFE” unless it is pushed all the way to the rear.

B. Take the Airsoft Gun “OFF SAFE”

Push the safety (I) forward and toward the “F” for “OFF SAFE”.

2. When the AIRSOFT GUN is “OFF SAFE” it can be red.

4. Install and/or Remove CO

Cartridge

A. Installing a New CO

Cartridge

CARTRIDGES MAY EXPLODE AT TEMPERATURES ABOVE 120°F 48.9°C. DO NOT MUTILATE OR INCINERATE CARTRIDGES. DO

NOT EXPOSE THEM TO HEAT OR STORE CO

CARTRIDGES AT TEMPERATURES ABOVE 120°F 48.9°C.

KEEP HANDS AWAY FROM ESCAPING CO

GAS. ESCAPING CO

GAS CAN CAUSE FROSTBITE IF ALLOWED TO COME IN CONTACT

WITH SKIN.

DO NOT STORE YOUR AIRSOFT GUN WITH A CO

CARTRIDGE IN IT. IF YOU KNOW YOU WILL NOT BE USING YOUR AIRSOFT GUN FOR

AN EXTENDED PERIOD OF TIME, EMPTY THE CO

CARTRIDGE AND REMOVE IT FROM THE AIRSOFT GUN STEP 3B. THIS IS VERY IMPORTANT TO REMEMBER,

AS IT WILL PROLONG THE LONGEVITY OF YOUR AIRSOFT GUN SEALS.

1. Put the AIRSOFT GUN “ON SAFE” (see Section 3A).

2. Make sure the AIRSOFT GUN is UNLOADED and POINTED IN A SAFE DIRECTION.

3. Holding the AIRSOFT GUN as shown (Fig. 3), pull the grip (H) back then slide to open position.

4. Locate the piercing wing (M) and turn it counter clockwise until the threaded portion is all the

way down as far as it will go.

5. Insert a new CO

cartridge into the AIRSOFT GUN with the small neck of the CO

cartridge

inserted rst. The round bottom of the CO

cartridge will rest on top of the piercing wing (M).

6. With your thumb and nger, turn the piercing wing (M) clockwise until tight, to pierce the CO

cartridge. If there is a hissing sound, continue to turn the piercing wing clockwise until it stops.

Never use any tool on the piercing wing. Over-tightening the CO

can cause injury to you or

damage to your gun.

7. To close the grip (H) gently push it down and forward until it is closed.

a. If the grip does not close, make sure the piercing wing (M) is not in the way.

b. If the grip comes completely o, line it up with the groove on the frame and slide the grip

forward to close.

B. Testing the CO

Cartridge

To make sure the cartridge has been pierced properly, point the AIRSOFT GUN in a SAFE DIREC-

TION, take “OFF SAFE” (see Step 3B) and pull the trigger.

2. If the AIRSOFT GUN does not make a popping noise after pulling the trigger, the CO

is not being discharged. In that event, repeat the last steps:

a. Put the AIRSOFT GUN “ON SAFE” (Step 2A), remove the grip.

b. Tighten the piercing wing a 1/4 turn. Replace the grip.

c. Point the AIRSOFT GUN in a SAFE DIRECTION and pull the trigger until there is a popping noise. The popping noise indicates that the AIRSOFT GUN is releasing CO

with each pull of the trigger and working properly.

NOTICE: We recommend the use of CROSMAN

POWERLET

cartridges. They are made to t your gun. Other brands of CO

cartridges may not t properly. If a CO

cartridge is forced

into place it may result in injury to you or damage to your gun.

C. Removing the CO

Cartridge

ALWAYS MAKE SURE THE CO

CARTRIDGE IS EMPTY BEFORE ATTEMPTING TO REMOVE IT FROM THE AIRSOFT GUN BY SLOWLY

TURNING THE WING COUNTERCLOCKWISE ALL THE WAY UNTIL YOU NO LONGER HEAR THE ESCAPE OF CO

GAS.

1. Put the AIRSOFT GUN “ON SAFE” (see Section 3A).

2. Make sure the AIRSOFT GUN is UNLOADED and POINTED IN A SAFE DIRECTION.

3. Holding the AIRSOFT GUN as shown (Fig. 4), pull the grip (H) back then slide to the open position.

4. Use one hand to hold the AIRSOFT GUN at the top of the receiver, being sure not to cover the muzzle.

5. Slowly turn the piercing wing (M) counter clockwise, to release the CO

. Be careful not to come in contact with the escaping gas.

6. Tip out the empty cartridge. It may be cold to the touch.

7. Tighten the cartridge piercing wing enough so that the grip will pass over it and close.

8. To close the grip (H), gently push it down and forward until it is closed.

a. If the grip does not close, make sure the piercing wing (M) is not in the way.

b. If the grip comes completely o, line it up with the groove on the frame and slide the grip forward to close.

5. Load and Unload Airsoft BBs

A. Loading The Airsoft Gun

Make sure the AIRSOFT GUN is “ON SAFE” (Section 3A) and pointed in a SAFE DIRECTION.

2. Locate the cylinder (E).

3. With the gun pointed in a safe direction, push the (I) safety (cylinder release) (Fig. 2) button forward

and hold.

4. While still holding the safety (cylinder release) (I) button forward, gently push the cylinder (E) from the right

side of the gun to the left side.

5. Locate the ejector rod (J)

6. Press the ejector rod removing the clip (L).

7. Place a 6mm airsoft BB into each cup-shaped opening of the clip and ensure the BBs t rmly in place.

8. With the exposed BBs facing forward, replace the loaded clip (L) into the opening of the cylinder chamber

(E). (See Fig. 4)

9. Push the cylinder back into the AIRSOFT GUN until it snaps into place.

10. Put the gun back “ON SAFE” (Section 3A).

11. After reading the entire manual, including the section on reviewing safety procedures, your AIRSOFT GUN is

now loaded and ready to re.

CAUTION: When you slide the safety (cylinder release) button forward to release the cylinder, you are taking the gun “OFF SAFE” and you will need to return it to “ON SAFE” (see

Section 3A).

IMPORTANT: To avoid jams, ensure the airsoft BBs are installed snugly in the clip.

CAUTION: Use .6mm BBs ONLY. NEVER REUSE BBs. USE OF ANY OTHER AMMUNITION CAN CAUSE INJURY TO YOU OR DAMAGE TO THE AIRSOFT GUN.

B. Unloading The Airsoft Gun

Fig. 2

OPEN

Fig. 3

Fig. 4

1 2 3

Inhaltsverzeichnis

Seite 1 - OWNER’S MANUAL

EVEN THOUGH YOU GO THROUGH THE UNLOADING PROCEDURE, CONTINUE TO TREAT THE AIRSOFT GUN AS THOUGH IT WERE LOADED. DO NOT POINT AT ANYTHING YOU DO NOT I

Seite 2 - MANUAL DEL PROPIETARIO

GF600Balines de 6 mm accionados por CO2Revólver de aire suave de 8 tiros(Acción sencilla o doble)MANUAL DEL PROPIETARIOCrosman Corporation7629 Routes

Seite 3 - MANUEL D’UTILISATION

GF600Alimenté au CO2, billes BB 6 mmRéplique airsoft de revolver 8 coups(Simple et double action)MANUEL D’UTILISATIONCrosman Corporation7629 Routes 5

Kommentare zu diesen Handbüchern

Keine Kommentare

Crosman ACG357 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sport und Erholung Crosman ACG357 herunter. Crosman ACG357 User Manual [en] [de] [fr] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sport und Erholung Crosman ACG357